RV Remodel Series-Flooring

Continuing my quickie makeover series in our new RV, “Road Kill”, I am delighted that I have finally zeroed in on the color scheme…light tan, chocolate and TEAL.  I’m going to salvage what I can of the existing improvements and make it work.  After all, a steal isn’t a steal if you pour money into it for cosmetics.  My goal for any improvement is how to get the most bang for your buck.  So teal we are sticking with.

For an RV, the ideal floor covering is one that is durable, flexible and will tolerate dirt, wet and easy to clean.  So I found myself looking at VINYL tile again.  An aisle I hardly ever venture down in the big home improvement stores.  To my surprise, they now carry a product called “Allure Ultra”.  Its a heavy duty vinyl product that is made to look like real wood.  I’m impressed to say, it really does look good…not some cheesy, grainy looking screening.  It carries a hefty warranty and is “WATER PROOF”; the cost was $2.97 psf and they have one that is less than $2 psf with the only difference being that it is considered water resistant.  It is installed similar to a floating laminate floor with a tongue and groove interlocking design.  There is no glue or other tools required except for a razor blade and straight edge.    Let’s see what happens!

Before I start, because the rental RV we had last summer had some sort of engine or drive train problem, it caused the RV to feel like a rolling oven inside.  The floors were so hot, it was hard to walk around and we were all fighting for the best spot by the air vents.  I did not want a similar experience this time.  I found a product called EZ Cool which is an automotive thermal insulation that is said to reduce noise and heat transfer.  I installed it  directly over the wood subfloors.

Next we laid new 1/4″ plywood directly over the thermal layer.

So now the new vinyl goes in.  I started with the wall opposite of the door and the directions call for working left to right:

A little trick I learned along the way is to leave the stuff sitting in sunlight before you score and snap it with your blade.  The heat makes it very pliable and easier to cut.  And now the finished project result; the Allure product really does look good!  I wouldn’t be bashful about putting this product in my home and I must say, we are beginning to have a classy looking RV.   I definitely give a thumbs up to this new flooring because it really is very easy to install yourself and looks really nice:

Here is the information from Home Depot’s site about the Trafficmaster Allure product:

Enjoy the resilience of 100% waterproof flooring and the look of real wood with new Exclusive Trafficmaster Allure Ultra flooring. The no-glue floating floor installs over most existing surfaces with a simple installation Click & Lock System. No underlayment, expansion joints or heavy tools are required to install. Allure Ultra is perfect for any room in your home, including basements and has a lifetime residential warranty and a 10-year commercial warranty.


  1. So glad I found this blog! DH and I just looked at that flooring yesterday while plotting our camper renovation. I’m glad to see it installed and that you are happy with it. Now I can’t wait to get started on ours!

  2. Glad I found you….this information will be very helpful. We are planning our reflooring renovation in our MH. I’m curious what you did at the base of the dinette? It looks like you have a slide out at that point (as we do) what did you ultimately do to finish that area? email me at ruthwt@gmail.com. Thanks!!

    • Having had the flooring down for more than a year, I will say that using 1/4″ plywood under was a mistake. The plywood is too thin and has warped in heat and humidity which has now caused the vinyl flooring to move around. I’m still happy with the flooring material, but if doing over, I would not do the 1/4″ plywood

        • I wouldn’t use the 1/4″ plywood at all and instead just go directly over the original wood decking subfloor that the RV comes with. The issue is that the 1/4″ plywood is too thin and the layers peel and warp easier than the heavier duty wood sub-floor the RV comes with. One drop of water, heat or humidity and the thin layers on the 1/4″ ply ripples like cardboard

Leave a Reply to MichelleGB Cancel reply

Your email address will not be published. Required fields are marked *